LaseView-LHB lineup

LaseView-LHB

Light receiving surface size	50 mm × 50 mm
Optical resolution	Around 100 μm（※1）
Measurement wavelength range	400 – 1100 nm （Focus is made with 532 nm or 1060 nm）
Power supply	Camera power supply 5 V About 250 mA (supplied from the USB) Motor power supply 6 V 100 mA or less (supplied from the included AC adapter)
Size(mm)	W154 × H82.5 × D130 (Excluding stand, cable and AC adapter)
Weight	2 kg or less (Excluding stand, cable and AC adapter)
Software	Comply with LaseView
Remark	In case of using small beam diameter, sufficient resolution is not available. Please make beam diameter 5 mm and over on your use. Frame rate decrease depending on the PC’s Computing ability or USB terminal. In case of using speckle reduction function, 10 – 20 image averaging process is required and 1 – 2 second (typical) measurement time is needed.
Price	contact us
Lead time	contact us

※ 1 Typically, the resolution as specified is obtained over the entire light-receiving surface. However, the inspection before shipment is limited to the center.

Diagram

LaseView-LHB External view

Catalog

LaseViewLHB Catalog

LaseView-LHB-GigE

Interface GigE type
（The basic usage is the same as the above LaseView-LHB. Only the differences are listed.）

Power supply	Camera power supply 12 V About 400 mA (supplied from the included AC adapter) or 48V (supplied from PoE compatible devices via LAN cable) Motor power supply 6 V, 100 mA or less (supplied from the included AC adapter)
Size(mm)	W168 × H82.5 × D130 (Excluding stand, cable and AC adapter)
Remark	LAN cable is not included. Cable with 6 and over is recommended.
Price	contact us
Lead time	contact us

Diagram

LaseView-LHB-GigE External view

＜About the configuration of LaseView-LHB-GigE＞
※ USB 3.0 connector is used when connecting to a PC.
※ The external trigger connector is used when taking an external trigger.
※ The motor power connector and motor switch are used when using the speckle reduction function.

Catalog

LaseViewLHB Catalog

Trial / Price / Inquiry

LaseView-LHB-100

Light receiving surface size	100 mm × 100 mm
Optical resolution	Around 200 μm（※1）
Measurement wavelength range	400 – 1100 nm （Focus is made with 532 nm or 1060 nm）
Power supply	Camera power supply 4.5 to 5.5 V About 250 mA (supplied from the USB) Motor power supply 6 V 100 mA or less (supplied from the included AC adapter)
Size(mm)	W208 × H137 × D173 (Excluding stand, cable and AC adapter)
Weight	2.5 kg or less (Excluding stand, cable and AC adapter)
Software	Comply with LaseView
Remark	In case of using small beam diameter, sufficient resolution is not available. Please make beam diameter 10 mm and over on your use. Frame rate decrease depending on the PC’s Computing ability or USB terminal. In case of using speckle reduction function, 10 – 20 image averaging process is required and 1 – 2 second (typical) measurement time is needed.
Price	contact us
Lead time	contact us

※ 1 Typically, the resolution as specified is obtained over the entire light-receiving surface. However, the inspection before shipment is limited to the center.

Diagram

LaseView-LHB-100 External view

Catalog

LaseViewLHB Catalog

Trial / Price / Inquiry

LaseView-LHB-NIR-GigE

Light receiving surface size	50mm × 50mm
Optical resolution	Around 400 μm（※1）
Measurement wavelength range	950 – 1700 nm （Focus is made with 1310 nm）
Power supply	12V, 10W or less (Supplied from the included AC adapter)
Size(mm)	W195 × H83 × D196 (Excluding stand, cable and AC adapter)
Weight	2.5 kg or less (Excluding stand, cable and AC adapter)
Software	Comply with LaseView
Remark	Please use a CAT5E or CAT6 compatible LAN cable. (LAN cable is not included.) In case of using small beam diameter, sufficient resolution is not available. Please make beam diameter 10 mm and over on your use. Frame rate decrease depending on the PC’s Computing ability or USB terminal. In case of using speckle reduction function, 10 – 20 image averaging process is required and 1 – 2 second (typical) measurement time is needed.
Price	contact us
Lead time	contact us

※ 1 Typically, the resolution as specified is obtained over the entire light-receiving surface. However, the inspection before shipment is limited to the center.

Trial / Price / Inquiry

LaseView-LHB-100-NIR-GigE

Light receiving surface size	100mm × 100mm
Optical resolution	Around 800 μm（※1）
Measurement wavelength range	950 – 1700 nm （Focus is made with 1310 nm）
Power supply	12V, 10W or less (Supplied from the included AC adapter)
Size(mm)	W215 × H137 × D219 (Excluding stand, cable and AC adapter)
Weight	2.5 kg or less (Excluding stand, cable and AC adapter)
Software	Comply with LaseView
Remark	Please use a CAT5E or CAT6 compatible LAN cable. (LAN cable is not included.) In case of using small beam diameter, sufficient resolution is not available. Please make beam diameter 10 mm and over on your use. Frame rate decrease depending on the PC’s Computing ability or USB terminal. In case of using speckle reduction function, 10 – 20 image averaging process is required and 1 – 2 second (typical) measurement time is needed.
Price	contact us
Lead time	contact us

※ 1 Typically, the resolution as specified is obtained over the entire light-receiving surface. However, the inspection before shipment is limited to the center.

Trial / Price / Inquiry

LaseView-LHB-VISNIR-GigE

Light receiving surface size	50mm × 50mm
Optical resolution	Around 150 μm（※1）
Measurement wavelength range	400～1700nm （Focus is made with 1310 nm）
Power supply	Undecided (Supplied from the included AC adapter)
Size(mm)	W195 × H83 × D196 (Excluding stand, cable and AC adapter)
Weight	2.5 kg or less (Excluding stand, cable and AC adapter)
Software	Comply with LaseView
Remark	Please use a CAT5E or CAT6 compatible LAN cable. (LAN cable is not included.) In case of using small beam diameter, sufficient resolution is not available. Please make beam diameter 10 mm and over on your use. Frame rate decrease depending on the PC’s Computing ability or USB terminal. In case of using speckle reduction function, 10 – 20 image averaging process is required and 1 – 2 second (typical) measurement time is needed.
Price	contact us
Lead time	contact us

※ 1 Typically, the resolution as specified is obtained over the entire light-receiving surface. However, the inspection before shipment is limited to the center.

Diagram

LaseView-LHB-VISNIR-GigE External view

Catalog

LaseViewLHB Catalog

Trial / Price / Inquiry

LaseView-LHB-100-VISNIR-GigE

Light receiving surface size	100mm × 100mm
Optical resolution	Around 300 μm（※1）
Measurement wavelength range	400～1700nm （Focus is made with 1310 nm）
Power supply	Undecided (Supplied from the included AC adapter)
Size(mm)	W215 × H137 × D219 (Excluding stand, cable and AC adapter)
Weight	2.5 kg or less (Excluding stand, cable and AC adapter)
Software	Comply with LaseView
Remark	Please use a CAT5E or CAT6 compatible LAN cable. (LAN cable is not included.) In case of using small beam diameter, sufficient resolution is not available. Please make beam diameter 10 mm and over on your use. Frame rate decrease depending on the PC’s Computing ability or USB terminal. In case of using speckle reduction function, 10 – 20 image averaging process is required and 1 – 2 second (typical) measurement time is needed.
Price	contact us
Lead time	contact us

※ 1 Typically, the resolution as specified is obtained over the entire light-receiving surface. However, the inspection before shipment is limited to the center.

Diagram

LaseView-LHB-100-VISNIR-GigE External view

Catalog

LaseViewLHB Catalog

Trial / Price / Inquiry

LaseView-LHB-100-WA

Light receiving surface size	100 mm x 100 mm (horizontal x vertical)
Optical resolution	Approx. 200 µm (at the centre of the photosensitive area)
Approximate measurement power density	0.1～100 W/cm2 (sensitivity adjusted according to exposure time)
Incident power density	Max. 100 W/cm2
Total incident power	Max. 10 W
Allowable incident light angle	±70°
Measurement wavelength range	400-1100 nm (focus adjusted at specified wavelength at time of shipment)
Number of CCD effective pixels	2048 x 1536 (horizontal x vertical)
Number of acquired image pixels	1600 x 1600 (horizontal x vertical)
A/D conversion resolution	12 bit
Frame rate	60 fps (max)
Exposure time	25 μs～4 s
Interface	USB3.1
External trigger function	Yes (3.3 to 24 V)
Power supply	Camera power supply 4.75 – 5.25 V, approx. 360 mA (supplied via USB) Motor power supply 6 V, 100 mA or less (supplied by attached AC adaptor)
External dimensions	as shown in the attached diagram
Weight	2.5 kg or less (excluding stand, cables and AC adapter)
Software functions	LaseViewに準拠
Remarks	If the beam diameter is small, sufficient resolution will not be achieved. The beam diameter should be 10 mm or more. The frame rate may decrease depending on the computing power of the PC and the USB connection. When using the speckle reduction function, 10-20 images need to be averaged and a measurement time of 1-2 seconds (typical) is required. When using the speckle reduction function, 10 to 20 images need to be averaged, requiring a measurement time of 1 to 2 seconds (typical). Light-receiving sensitivity varies depending on the angle of incidence of the light beam.

Diagram

LaseView-LHB-100-WA External view

Trial / Price / Inquiry

LaseView LHB-UHP

Light receiving surface size	50 mm × 50 mm
Optical resolution	Around 100 μm（※1）
Indication of measurement power density	10～100 kW/cm2
Total incident power	Maximum 10 W
Incident power density	Up to 100 kW/cm² (High heat resistant screen)
Allowed incident light angle	±15°
Measurement wavelength range	400～1100 nm （Focus is made with 532 nm）
Image sensor pixel(mm)	1440 × 1080 （Horizontal × vertical）
Acquisition image pixel	1250 × 1250 （Horizontal × vertical）
A/D Conversion resolution	8 / 12 bit
Frame rate	160 fps
Exposure time	1 μs～30 s
Interface	USB3.0（miniB terminal）
External trigger	Yes（3.3～12 V / 820 Ω）
Power supply	Camera power supply 5 V, About 660 mA (supplied from the USB) Motor power supply 6 V, 100 mA or less (supplied from the included AC adapter)
Size(mm)	W154 × H82.5 × D164 (Excluding stand, cable and AC adapter)
Weight	2 kg or less (Excluding stand, cable and AC adapter)
Software	Comply with LaseView
Remark	In case of using small beam diameter, sufficient resolution is not available. Please make beam diameter 10 mm and over on your use. Frame rate decrease depending on the PC’s Computing ability or USB terminal. In case of using speckle reduction function, 10 – 20 image averaging process is required and 1 – 2 second (typical) measurement time is needed.
Price	contact us
Lead time	contact us

※ 1 Typically, the resolution as specified is obtained over the entire light-receiving surface. However, the inspection before shipment is limited to the center.

LaseView LHB-100-UHP

Light receiving surface size	100 mm × 100 mm
Indication of measurement power density	10～100 kW/cm2（UHP model）
Total incident power	Maximum 10 W
Allowed incident light angle	±15°
Optical resolution	Approx.200 μm
Measurement wavelength range	400～1100 nm（Focus adjusted at specified wavelengths）
Sensor effective pixels	2048×1536
Number of acquired image pixels	2000×2000
bit depth	8 / 16 bit
Frame rate	60 fps（Maximum）
Exposure time	25 μs～4 s
Interface	USB 3.0
Power supply	Camera power supply 5V (supplied from the USB)
Power supply	Motor power supply 6V (supplied from the included AC adapter)
Size(mm)	W208mm×H137mm×D173mm
Remark	Sufficient accuracy may not be achieved when measuring beam diameters below 20 times the optical resolution. The frame rate may decrease depending on the computing power of the PC, the state of the USB connection and the settings. When using the speckle reduction function, a measurement time of 1-2 s (typical) is required.
Price	contact us
Lead time	contact us

Trial / Price / Inquiry

LaseView LHB-200

Compare to third parties’ 200mm model, LHB-200 has following advantages;

All in one and compact.
No need to adjust by the users
Having a function to reduce speckle
Calibrated spatial scale
Calibrated spatial distortion and homogeneous of intensity
Less dependency of incident light angle (WA model is available for ±70°)

Light receiving surface size	200 mm × 200 mm
Optical resolution （※1）	Around 400 μm
Measurement wavelength range	400～1100 nm
Power supply	5V、Around700 mA （Supplied from the included USB）
Motor supply	6V、100 mA or less （Supplied from the included AC adapter）
Size（mm）	W389 × H258 × D268 (Excluding stand, cable and AC adapter)
Weight	8 kg or less (Excluding stand, cable and AC adapter)
Software	Comply with LaseView
Remark	In case of small beam diamater, sufficient resolution may not be available. Beam diameter 20 mm or more will be measurable. Frame rate may decrease due to PC’s computing power or USB (or Ethernet) ‘s connection. In case of using speckle reduction function, 10 – 20 image averaging process is required and 1 – 2 second (typical) measurement time is needed.
Price	contact us
Lead time	contact us

※１ According to product specification, resolution is available on whole area of light-receiving surface,
Inspection prior to shipment will be made only on the center of light-receiving surface.

Diagram

LaseView-LHB-200 External view

Catalog

LaseViewLHB Catalog

LaseView-LHB-200-VISNIR-GigE

Interface GigE type
（The basic usage is the same as the above LaseView-LHB. Only the differences are listed.）

Optical resolution	Around 600μm
Frame rate	60 fps （at maximum）
Measurement wavelength range	950～1700nm (Adjusted at specified wavelength)
Exposure time	6 μs～10 s
Interface	Gigabit Ethernet (1000BASE-T)
Power supply	12 V, 7 W (supplied by attached AC adaptor)
Motor supply	6 V, 100 mA or less (supplied by attached AC adaptor)
Remark	Use a LAN cable compatible with CAT5E or CAT6. (LAN cable not included).
Price	contact us
Lead time	contact us

Diagram

LaseView-LHB-200-VISNIR-GigE External view

LaseView-LHB-200-GigE

Interface GigE type
（The basic usage is the same as the above LaseView-LHB. Only the differences are listed.）

Frame rate	24 fps （at maximum）
Exposure time	20 μs～30 s
Interface	Gigabit Ethernet (RJ-45 connector)
Power supply	12 V About 400 mA (supplied from the included AC adapter) or 48 V (supplied from PoE compatible devices via LAN cable)
Motor supply	6 V 100 mA or less (supplied from the included AC adapter)
Remark	LAN cable is not included. Cable with 6 and over is recommended.
Price	contact us
Lead time	contact us

※１ According to product specification, resolution is available on whole area of light-receiving surface,
Inspection prior to shipment will be made only on the center of light-receiving surface.
※ Wireless LAN is not supported because the network must support Gigabit Ethernet (1000BASE-T).

Diagram

LaseView-LHB-200-GigE External view

Catalog

LaseViewLHB Catalog

Trial / Price / Inquiry

LaseView LHB-25

Light receiving surface size	25 mm × 25 mm
Optical resolution	Around 50 μm
Measurement wavelength range	400～1100 nm（Focus is made depending on the designated wavelength）
Power supply	5 V（Supplied from the included USB）
Motor supply	6 V（Supplied from the included AC adapter）
Size（mm）	W129 × H57.5 × D116
Remark	In case of small beam diamater, sufficient resolution may not be available.
	Frame rate decrease depending on the PC’s Computing ability or USB terminal.
	In case of using speckle reduction function, 1 – 2 second (typical) measurement time is needed.
Price	contact us
Lead time	contact us

※１ According to product specification, resolution is available on whole area of light-receiving surface,
Inspection prior to shipment will be made only on the center of light-receiving surface.

Diagram

LaseView-LHB-25 External view

Catalog

LaseViewLHB Catalog

Trial / Price / Inquiry

Specification

With LaseView-LHB, the measured large diameter beam illuminates an entrance window, the light diffused from the window is recorded by a CCD camera at the rear, which allows to measure large diameters. After several experiments, by using a particular window, the direct input of high-intensity beams of more than 100 W/cm2 was made possible and we succeeded in achieving both a high resolution and a uniform sensitivity.

model	LHB-25	LHB / LHB-GigE	LHB-NIR-GigE	LHB-VISNIR-GigE	LHB-UHP
Light receiving surface size (mm)	25 × 25	50 × 50	50 × 50	50 × 50	50 × 50
Optical resolution （※ 1）	Around 50 μm	Around 100 μm	Around 400 μm	Around 150 μm	Around 100 μm
Indication of measurement power density （※ 2）	0.1~100 W/cm2 （※ 2）	0.1～100 W/cm2 （※3）	0.1～100 W/cm2	0.1～100 W/cm2	10～100 kW/cm2
Total incident power （※4）	Maximum 10W	Maximum 10W	Maximum 10W	Maximum 10W	Maximum 10W
Allowed incident light angle （※5）	±15°	±15°	±15°	±15°	±15°
Measurement wavelength range （default focus wavelength）	400～1100 nm （Focus is made depending on the designated wavelength）	400～1100 nm （532 nm or 1060 nm）	950〜1700 nm （1550 nm）	400～1700nm （1310nm）	400～1100 nm （532 nm）
Image sensor pixel(mm) （Horizontal × vertical）	1440 × 1080	1440×1080	320 × 256	1280 × 1024	1440 × 1080
Acquisition image pixel （Horizontal × vertical）	1600 × 1600	1600×1600	400 × 400	1250 × 1250	1250 × 1250
A/D Conversion resolution	8 / 16 bit	8 / 16 bit	8 / 10 / 12 / 14 bit	8 / 10 / 12 bit	8 / 12 bit
Frame rate （at maximum）	238 fps	238 fps	228fps	130 fps（8 bit）	160 fps
Exposure time	1 μs ~ 30 s	1 μs~30 s	0.001 ms～ 10 ms	–	1 μs～30 s
Interface	USB 3.0	USB3.0（miniB） / GigE（RJ-45）	GigE（RJ-45）	GigE（RJ-45）	USB3.0（miniB）
External trigger	–	Yes （3.3～24 V / 3.5 mA）	–	–	Yes

model	LHB-100	LHB-100-NIR-GigE	LHB-100-VISNIR-GigE	LHB-100-WA
Light receiving surface size (mm)	100 × 100	100 × 100	100 × 100	100 × 100
Optical resolution （※ 1）	Around 200 μm	Around 800 μm	Around 300 μm	Around 200 μm
Indication of measurement power density （※ 2）	0.1～100 W/cm2 （※3）	0.1～100 W/cm2	0.1～100 W/cm2	0.001～1 W/cm2
Total incident power （※4）	Maximum 10W	Maximum 10W	Maximum 10W	Maximum 10W
Allowed incident light angle （※5）	±15°	±15°	±15°	±70°
Measurement wavelength range （default focus wavelength）	400～1100 nm （532 nm or 1060 nm）	950〜1700 nm （1550 nm）	400～1700nm （1310nm）	400～1100 nm
Image sensor pixel(mm) （Horizontal × vertical）	2048×1536	320 × 256	1280 × 1024	2048 × 1536
Acquisition image pixel （Horizontal × vertical）	1600 × 1600	400 × 400	1250 × 1250	1600 × 1600
A/D Conversion resolution	8 / 16 bit	8 / 12 bit	8 / 10 / 12 / 14 bit	12 bit
Frame rate （at maximum）	60 fps	228fps	130 fps （8 bit）	60 fps
Exposure time	1 μs~30 s	0.001 ms～ 10 ms	–	25 μs～4 s
Interface	USB3.0（miniB）	GigE（RJ-45）	GigE（RJ-45）	USB3.1
External trigger	Yes （3.3～12 V / 820Ω）	–	–	Yes （3.3～24 V）

model	LHB-200 / LHB-200-GigE	LHB-200-VISNIR-GigE
Light receiving surface size (mm)	200 × 200	200 × 200
Optical resolution （※ 1）	Around 400 μm	Around 600 μm
Indication of measurement power density （※ 2）	0.1～100 W/cm2	0.1～100 W/cm2
Total incident power （※4）	Maximum 10W	Maximum 10W
Allowed incident light angle （※5）	±15°	±15°
Measurement wavelength range （default focus wavelength）	400～1100 nm	950～1700 nm
Image sensor pixel(mm) （Horizontal × vertical）	2448 × 2048	1280 × 1024
Acquisition image pixel （Horizontal × vertical）	2500 × 2500	1250 × 1250
A/D Conversion resolution	8 / 16 bit	8 / 10 / 12bit
Frame rate （at maximum）	38 fps	60 fps
Exposure time	25 μs～4 s / 20 μs～30 s	6 μs～10 s
Interface	USB3.0（3.0 Micro B）/ GigE（RJ-45）	Gigabit Ethernet (1000BASE-T)
External trigger	Yes （3.3～12 V / 820 Ω）	–

※ 1 Typically, the resolution as specified can be obtained on the entire surface of the light receiving surface. However, the inspection before shipping is only in the central part.
※ 2 Sensitivity adjusted according to exposure time
※ 3 1 mW / cm2 ~ by replacing the ND filter (NDFS-CA50)
※ 4 Customizable for large total incident power.
※ 5 Customizable for large allowable incident light angles.
※ Customizable in the infrared region.
※ Wireless LAN is not supported because the network must support Gigabit Ethernet (1000BASE-T).